How to Drain a Pool Using the Pool Pump
Every time I go into the pool, I feel submerged in cool, clean water. But how can we identify how clean the water is? Sure, you use sanitizer the way you’re awaited and clean the pool. But if it’s been a few years since you filled your pool. It may be time to drain it and begin fresh.
However, there is one element to consider that can’t just be wretched away with what you add to your pool: the residue of these chemicals, combined with dirt, debris, and other contaminants. These are called total dissolved solids (TDS), and once they build up for too long, they can seriously interfere with your water’s chemistry.
Draining your pool is essential planning in pool maintenance that you should do carefully. There are many ways to drain a pool, but here we are discussing how to drain a pool using the pool pump.
And no matter how well you take care of your pool, there will need repairs. And it’s hard to fix overcome those spots on the inground floor without replacing the water first. So, take a little time to learn how to drain a pool using a pool pump.
But for anyone who’s had a pool for an extended period, there will be time to drain it. It’s a weekly, monthly, or even yearly process, which is a good thing you should know. You can equitably expect to need to drain your pool every few years.
How to drain a pool using the pool pump?
Let it go and start a new technique than using a chemical pool pump. For chemical-using agents in the pool, you ensure that water is sitting in your pool for quite some time. That’s why we add chemicals like chlorine.
Whether you’re draining a pool for winter or repairs, you should know how to drain it using the pool pump; it’s a precision task.
Draining a pool doesn’t require many tools, but it has to be done under the right conditions and with enough preparation.
You’ll have to find a suitable spot to drain tens of thousands of gallons of water safely and pay attention to chemical levels before draining the pool.
The following methods are given below on how to drain a pool using the pool pump.
A Submersible Pump
Submersible pumps to drain a pool. The maximum recommended discharge rate is 720 gallons an hour.
1. Clean the Pool
The last thing you want to deal with is any obstruction while draining the pool. Use a spoon to remove as much debris as possible and place it into the garbage.
2. Discharge Hose onto Pump
Once the discharge hose is attached to the pump, stipulate the discharge hose as evenly as possible to prevent any clogs during draining.
3. Start Pumping
Once you have the pump in hand, you can drain the pool. Make sure the power cord can reach the bottom of the deep end. Make sure the pump is plugged in. Attach a rope to the cord to help lead the pump to the bottom.
When the pump has reached the bottom, remove the rope. Observe the draining process to avoid backup and prevent the pump from sucking in the air. If a pump isn’t submerged in water, it can ruin the pump.
4. Open Hydrostatic Pressure Relief Valve
To stop the bottom of the pool from popping up, allow a hydrostatic pressure relief valve that allows any groundwater under your pool to escape.
How to drain the pool with the Hayward pump?
The process of how to drain a pool using the pool pump with the Hayward pump: To use a Hayward pump, you should know about the setting and methods. The following are given below:
1. To set It up
You, Will, require at least a 100-foot outlet hose, a hose connector, and a hose clamp.
2. Attach the hose pipe to the sewer and pump
Connect the pump to the sewer drainage pipe using a hose pipe. To make sure the hydrostatic valve is open.
3. Fall the pump in the shallow end
Immersed the pump into the water should be at the shallow end.
4. Start draining
Then start draining the water. Keep an eye on the entire process and be ready to end.
How to drain a swimming pool using the pool pump?
Every owner of a swimming pool knows that draining water is mandatory. For many reasons draining is necessary, I.e., replacing your pool liner. If you do not drain the water, your pool can be exposed to potential damage. It’s essential to know how to drain a pool by using pool pump. So you can minimize the risk of damage.
It’s essential to know a method of how to drain a swimming pool using the pool pump properly. Find out how to drain a pool below.
Choose your to-drain method:
Draining Pool Water Using an Electric Pool Pump
To drain your pool water using an electric pool pump, follow the steps below:
- Deep down the pump’s hose into the water as the pool centre.
- Place the outlet hose of the pump. Make sure to choose level ground where to drain water.
- Turn on the pool pump.
- Turn the equipment off once the water level is too low for further draining.
How to pump water out of the pool?
When it’s time to empty your pool, there are two main options that pool owners typically choose from when ready to drain: an electric pump or a garden hose siphon.
Either choice will work to drain your pool water. It’s a matter of preference, time, and equipment on hand. Here is a round-up of each drain method and the steps needed to complete the process: In this article, we will explain how to pump water out of the pool.
1. Empty the Water Using a Filter Pump
First, you’ll need to properly check your pool to ensure a drainage mechanism since some pools are available with this. At this point, you will need to open the tap, which will be enough to let the water out.
Also, in cases like these, we think the best bet is to use a filter pump. Upon using this, you should inspect to see if the shaft is rotating as it should. After, it would help if you closed the cleaner’s tap and the skimmer.
Ensure that the filter is correctly placed in the drainage position, and you must adequately unlock the motor shaft since you should remove all the water from the pool.
2. Use a Submersible Pump
If it’s a case where your poodle doesn’t come equipped with a filter pump, you can also take the time out to use a high-end water drain pump for the pool; for this, we think it is best to go with a submersible pump.
Make sure the pump is available with a hose to drain the water at the other end.
How to pump water out of in-ground level?
As likely as not to know, it’s never easy to drain yours in the ground.
But for anyone who’s had a pool for long adequately, the time to drain will come. In-ground pools could get seriously wrecked, so draining is mandatory. I’ll explain how to drain a pool by using pool pump.
Draining an in-ground pool is much more involved than draining an above-ground one.
You know the dangers and how to avoid them. Follow these steps on how to pump water out in ground level:
1. Submersible pump
Place the pump into the bottom of the centre of the pool. Disable the pool pump. Many of these pieces of the pump are liquid-cooled. When it leaves, they will overheat as the water level drops.
2. Start draining
Attach a hose from the pool to the drain point Plug the pump into the pool’s GFCI outlet. Monitor the pump is running. Using a large pair of pliers, unscrew the plugs and allow the groundwater to enter the pool. There can be quite a bit of flow and pressure, so don’t be alarmed. Also, the plugs are likely to become damaged, so be sure to have replacements on hand.
3. Remove the pump
Your in-ground pool has hydrostatic plugs. Removing all of them is best but make the one in the deep end. It will release that upward pressure the quickest.
4. Relief valves
Using this method, you should be able to avoid pool pop. Just be sure to replace the hydrostatic plugs and relief valve before refilling.
How to pump water out of above-ground pool?
How to Drain a pool by using pool pump:
- Draining an above-ground pool is relatively easy. Following these steps:
- Switch off the pool pump and any other electrical components.
- Attach the hose from the pool to the drain point.
- Attach the hose to the submersible pump and place it into the bottom of the pool.
- Attach the pump directly into the pool’s GFCI ground fault circuit interrupter outlet. The pump should be running.
- Keep an eye on the end of the hose to ensure that the water’s flowing properly into the drain point.
- Check on the pool intermittently.
- Draining a pool takes up to 14 hours, depending on the size, so drain it daily. Do not let the pump run dry or it can become damaged.
Water pump to drain pool Home Depot?
Water pumps are used for residential purposes, too, for draining. Following given below:
- flooded basement
- draining a hot tub
- for a sprinkler system
Types of Pumps
- The BURCHAM automatic submersible utility pump is ideal for general water transfer applications, including draining basements, spas, pools, and flat roofs.
- Submersible utility pump: If you need to drain an area like a flooded basement or pool cover, submerge the pump. This pump is used if you need to drain a water heater or fish tank.
- It also removes water from areas like crawl spaces, window wells or other low-lying areas.
FAQS: How to Drain a Pool Using the Pool Pump?
We can quickly drain water from the pool in many ways. You can either use Manual Pump or an Electrical Pump. For the manual pump, pull the end of the hose out of the water. Place the end you're holding on the ground at a lower level than your pool's. Water line, when you move your hand away, the water should start siphoning.
For electrical pumps, using a submersible pump is the fastest way to drain your pool. It acts like a vacuum to remove water quickly, but you'll need to monitor it while running. A garden hose siphon is another option for draining water, but it will take much longer.
sump pump is a submersible pump and is integral to flood prevention in many homes. Here’s how to use a sump pump to drain water:
- Once the basin collects water, the float switch triggers, and the pump activates.
- Water is then pushed up through a discharge pipe. And safely away from your home.
- As the water level drops, the float switch will disengage and turn off the pump.
Draining a pool is essential and mandatory in the right way. There are many ways through which we can repair when needed and change when water is not clean.
From the above detailed guide you now know How to Drain a Pool Using the Pool Pump. Visiting our website you will see a bunch of amazing content regarding pools. Don’t miss out and enjoy.